Short answer: a test pressing is one of the first few records pressed from your stampers, before the run. It is the only moment you hear your record as it will really exist, and the last chance to fix a problem from cutting, plating or pressing. Listen to every copy, note the side and the minute of anything you hear, and remember that a test pressing is not the final run: some things you hear will not be there, and the plant can tell you which.
What is a test pressing?
Once your audio is cut and the stampers are made, the plant presses a handful of records before anything else, usually somewhere between three and ten. These are the test pressings. They normally come in plain white sleeves with blank or simple labels, because only the sound and the vinyl are being checked.
You listen, and then you approve them or tell the plant what is wrong. Only after your approval does the full run start. If you want to see where this sits in the whole process, read how a vinyl record is made.
Why does it matter so much?
Because a problem that reaches the full run is on every record you sell. A test pressing can catch:
- cutting problems: distortion, sibilance, a side that is too long or too loud for the groove;
- plating problems: faults in the stampers that repeat on every copy;
- pressing problems: noise, non-fill (a groove that did not form properly), warps, an off-centre hole.
Approving a test pressing takes a few days. Pressing a bad run again takes weeks, and costs far more.
What you may hear
It helps to have names for what you hear, so you can describe it clearly:
- Tick: one short, sharp sound, mostly in the middle and high frequencies.
- Pop: one sharp sound across the whole range, fuller and louder than a tick.
- Crackle: a run of small, sharp noises, like frying. Easiest to hear in quiet passages.
- Static: a soft hiss with no sharp edge, like white noise under the music.
- Distortion: the sound breaks up and loses clarity. It often shows towards the end of a side, where the groove is tighter.
- Sibilance: harsh, splashy S sounds in vocals, or cymbals that fizz.
- Pre-echo: a faint ghost of a loud sound, heard just before it arrives.
How to judge your test pressing
Listen to every copy
A problem can be on one copy and not on the others. Check each test pressing you received, not just the first one out of the box, and write down which copy you heard something on.
Same place on every copy, or not?
This is the most useful question. A sound at the same moment on every copy is in the cut or the stampers, and it needs fixing before the run. A sound that moves, or appears on a single copy, is usually a one-off from pressing.
The test is not the final run
Test pressings are pressed in a short run, before the press has settled at its working heat and cooling. A flaw can show on a test pressing and not on the finished records, and the other way round. So do not approve or reject on a single tick alone: tell the plant what you hear and where, and let them tell you whether it will carry into the run.
Listen closely at the start and the end
Pay attention to the first and last 30 seconds of each side, and to the last track, where the groove is tightest and distortion shows first.
Write it down
For each issue, note the side, the minute and second, the copy, and what you hear. Listen twice, so you know it is on the record and not in your system.
Look at them too
In good light, check that the records are flat, with no scuffs, marks or an off-centre hole.
Your turntable matters
A test pressing can only sound as good as the system that plays it. An old or badly set-up turntable adds its own noise, distortion and speed errors, and can make a good pressing sound faulty. Before you listen:
- make sure the stylus is clean and not worn;
- check that the cartridge is aligned;
- set tracking force and anti-skate as the cartridge maker recommends;
- check the turntable runs at the right speed and stands level.
If you can, listen on a second system too. A problem that appears on both is on the record.
A tool to help you listen
We built a free test pressing check for exactly this. Record each copy, add the recordings next to your master as V1, V2, V3, and it lines them up and shows where to listen: clicks and pops, skips, speed, balance and surface noise, with a button to hear the master and each copy at the same moment. Your files never leave your computer.
FAQ
How many test pressings will I get?
Usually a handful, often between three and ten, depending on the plant and the order.
Why does my test pressing sound noisier than a normal record?
Test pressings are made in a short run before the press settles at its working heat and cooling, so they can be a little noisier or slightly warped. Tell the plant what you hear: many of these sounds do not carry into the final run.
Should I reject a test pressing for a single click?
Not on its own. Check whether it is on every copy at the same moment. If it is, it is in the cut or the stampers and should be fixed. If it is on one copy only, it is usually a one-off.
How long do I have to approve a test pressing?
Plan a few days to listen carefully and send your notes. The run starts only after your approval.
Planning a release? Tell us the format, quantity and finish in our configurator, and we will reply with a quote by email.