Short answer: a vinyl record is made in seven steps. The audio is mastered for vinyl, cut into a lacquer disc, turned into metal stampers, checked with a test pressing, then pressed from hot PVC, checked, sleeved and shipped. Plan for six to eight weeks from approved files to finished records.

If you are running a vinyl project for a client, knowing these steps helps you plan the budget, the timeline and the questions you will get. Here is each one in plain words.

Step 1: Mastering for vinyl

Mastering prepares the music for the groove. A vinyl master is not the same as a streaming master.

Why? Because the groove is a physical thing. Very loud masters, heavy bass and sharp "s" sounds (sibilance) can make the needle jump or distort. A vinyl master balances level, bass, stereo width and side length so the cut works.

What agencies should know:

  • Ask for lossless files: WAV or AIFF, 24-bit, 48 or 96 kHz. Never MP3.
  • About 16 minutes per side is comfortable. Around 25 minutes is the limit, and the record gets quieter as the side gets longer.
  • Track order matters. The inner grooves near the label are harder to play, so put loud, bass-heavy songs early on a side.

Step 2: Lacquer cutting

A cutting engineer plays the master into a cutting lathe. A heated stylus engraves the groove into a soft lacquer-coated aluminium disc, in real time.

That lacquer is the physical original. Every record in the run comes from it. A 20-minute side takes 20 minutes to cut, and a mistake means cutting again.

Some plants cut into copper instead of lacquer. This is called DMM (Direct Metal Mastering) and skips one plating step. Both methods produce good records.

Step 3: Electroplating (making the stamper)

The lacquer is too soft to press records from. So it is coated with silver and then nickel in a chemical bath. When the metal is peeled off, you get a negative copy: ridges instead of grooves.

  • The father is that first metal negative.
  • From the father, a mother (a positive) can be grown.
  • From the mother come the stampers, the negatives that actually press the records.

For short runs, the father can go straight into the press. For longer runs, the mother lets the plant grow new stampers when the first ones wear out. One stamper presses roughly a thousand records, give or take, depending on the plant and the material.

Step 4: Test pressing

Before the full run, the plant presses a handful of records: the test pressings. The artist or label listens and approves them.

This is the only moment you hear the record as it will really exist. Check:

  • the track order and where each side starts and ends,
  • the level and the bass,
  • clicks, pops or distortion that are not in the master.

Listen on a good turntable with a clean needle. If something is wrong, note the side, the minute and what you hear.

Approving a test pressing takes a few days. Pressing a bad run again takes weeks and costs far more. We treat test pressings as part of the job, not an extra.

Step 5: Printing labels, sleeves and extras

Labels are the round paper centres of the record. They get pressed into the vinyl, so they must be printed before pressing starts. Sleeves, inserts, posters and booklets are printed in parallel.

Print files should be CMYK, at least 300 dpi, at 1:1 scale, with bleed. Use the plant's templates. A wrong spine width is one of the most common print mistakes. A single LP needs about 3 mm, a double LP about 5 mm.

Step 6: Pressing

This is the part people picture. The plant loads PVC compound (small pellets) into an extruder that heats it into a soft, warm lump called a puck or "biscuit". The puck goes between the two stampers, with a label on each side.

The press closes with a lot of force and steam heat. The PVC flows into every groove. Cold water then cools the mould, the press opens, and the extra material around the edge (the flash) is trimmed off. A 12-inch record takes around 30 seconds.

Coloured vinyl and effects like splatter or marbling happen here. They come from how the coloured pellets are mixed and placed. That is why every splatter record looks a little different.

Step 7: Quality control, packing and shipping

Records are checked by eye as they are sleeved, and sampled by ear. Warps, dents, dirt, off-centre holes and noisy pressings are set aside.

The good copies go into inner sleeves, then jackets, then shrink-wrap if you want it. Then they are boxed and shipped.

Pressing is a physical process, so the final count can be up to about 10% more or less than ordered on runs of up to 1,000 copies, and a few dozen copies either way on larger runs. That is standard in the European industry. You pay for what you receive.

How long does it take to make a vinyl record?

Plan for six to eight weeks from a confirmed order with approved audio and artwork. Special finishes and busy seasons (autumn, before the holidays) can add time.

A rough timeline:

Stage Typical time
Cutting and plating 1–2 weeks
Test pressings to you 2–4 weeks after files
Your approval a few days
Printing, pressing, QC, packing 3–4 weeks
Shipping depends on destination

The single biggest delay we see is not the factory. It is waiting for final files, artwork corrections or test pressing approval. Build that into the plan.

What do you need to start a vinyl pressing?

  1. Final audio, mastered for vinyl, as WAV or AIFF.
  2. Print-ready artwork on the right templates.
  3. Confirmation that mechanical rights are cleared.
  4. Decisions on format: size (7", 10", 12"), weight (140g or 180g), colour, packaging and quantity.

Our minimum run is 200 copies. The more you press, the lower the price per record.

FAQ

How is a vinyl record made, in one sentence?

Audio is cut into a lacquer disc, turned into metal stampers, and pressed into hot PVC under high pressure, then checked, sleeved and shipped.

What are vinyl records made of?

PVC (polyvinyl chloride), usually a PVC compound with small amounts of stabilisers, lubricants and pigment. Read more in What is PVC and how is it made?.

Do I need a test pressing?

Yes. It is the only way to hear the finished record before hundreds of copies exist.

How many records can one stamper press?

Roughly a thousand, depending on the material and the plant. Longer runs use extra stampers grown from the same mother.

What is the minimum order for vinyl pressing?

With us, 200 copies. There is no maximum.


Ready to plan a pressing? Describe the project in our configurator and you will get a quote by email. Or read next: 140g vs 180g vinyl: which should you choose?